CONTADORES OMRON

H7CN-XLN

H7CX-A-N

 
Function 1 Stage Preset Counter / Total Preset Counter
Preset stages 1stages
Rated supply voltage 100 to 240 VAC 50/60 Hz
Operating voltage range 85% to 110% of rated supply voltage
Power consumption Approx. 9.4 VA
External power supply 12 VDC (+/- 10%) 100 mA
Counter (Count range) -99999~999999
Counter (Max. counting speed) 30 Hz/5 kHz (switching) (Minimum counting input signal width: 16.7 ms(ON/OFF ratio: 1:1)/0.1 ms(ON/OFF ratio: 1:1))
Common setting for CP1 and CP2
Counter (Input mode) Increment decrement or increment/decrement (UP/DOWN A (command input), UP/DOWN B (individual input) and UP/DOWN C(quadrature input))
Counter (Output modes) N / F / C / R / K-1 / P / Q / A / K-2 / D / L
Counter One-shot time) 0.01 to 99.99 s variable
Counter (Reset system) External, manual and automatic reset (internal according to C, R, P and Q mode operation)
Input signal CP1 / CP2 / Reset / Total reset
Input method No-voltage/Voltage input (selectable)
No-voltage input (No-contact input) Short-circuit (ON) impedance: 1 kΩ
Leakage current (0 Ω): 12 mA
Residual voltage: 3 V max.
Open circuit impedance: 100 kΩ
Maximum voltage: 30 V
No-voltage input (Contact input) Use a contact which can adequately switch 5 mA at 10 V.
Voltage input Hight level: 4.5 to 30 VDC
Low level: 0 to 2 VDC
Input resistance: 4.7 kΩ
Applicable two-wire sensor leakage current: 1.5 mA
Switching capacity: 5 mA
Residual voltage: 3 V
Operating voltage: 10 VDC
Minimum input signal width External reset: 1 ms/20 ms (selectable)
Standby time 290 ms
Control output (Contact output) SPDT
Switching capacity: 3 A at 250 VAC/30 VDC, resistive load (cos phi=1)
Minimum applicable load: 10 mA at 5 VDC (failure level:P reference value)
Display method 7-segment negative transmissive LCD
Digits 6digits
Character height Count value: 10 mm (Red, green or orange programmable)
Zero suppression: Equipped
Set value: 6 mm (Green)
Prescaling function Provided (0.001 to 99.999)
Decimal point adjustment Rightmost 3 digits
Key protection Key protect Switch
Teaching function Not provided
Batch counting function Not provided
Communications Not provided
Memory backup EEP-ROM (Number of rewite: 100000 times min.Service life: Approx. 10 years min.)
Surrounding air temperature Operating: -10 to +55 ℃
Storage: -25 to +70 ℃
Ambient humidity Operating: 25 to 85%
Storage: 25 to 85%
Insulation resistance 100 MΩ min. (at 500 VDC)
Between current-carrying terminals and exposed non-current-carrying metal parts / Between non-continuous contacts
Dielectric withstand voltage Between current-carrying metal parts and non-current-carrying metal parts:2000 VAC 50/60 Hz for 1 min
Between power terminals and control input terminals:2000 VAC 50/60 Hz for 1 min
Between control output,power supply, and input circuit:2000 VAC 50/60 Hz for 1 min
Between non-continuous contacts:1000 VAC 50/60 Hz for 1 min
Impulse withstand voltage Between power terminals:3.0 kV
Between current-carrying terminal and exposed non-current -carrying metal parts:4.5 kV
Noise immunity Between power terminals:+/- 1.5k V
Between input terminals:+/- 600 V
Square-wave noise by noise simulator (Pulse width: 100 ns/1 us, 1-ns rise)
Static immunity 8 kV (malfunction), 15 kV (destruction)
Vibration resistance (Destruction) 10 to 55 Hz with 0.75 mm single amplitude for two hours each in three directions
Vibration resistance (Malfunction) 10 to 55 Hz with 0.35 mm single amplitude for ten minutes each in three directions
Shock resistance (Destruction) 300 m/s**2 three times each in six directions
Shock resistance (Malfunction) 100 m/s**2 three times each in six directions
Mechanical life expectancy 10,000,000 operations min.
Electrical life expectancy 100,000 operations min. (3 A at 250 VAC, resistive load)
Degree of protection Case front: IEC IP66, UL508 Type 4X (indoors) (when using the Y92S-29 Waterproof Packing)
Mounting method Flush mounting
External connection method Screw terminals
Case color Black (Munsell N1.5)
Accessories Flush mounting adapter / Waterproof rubber packing / Shock Prevention Cover
Weight Approx. 130 g

 

Hoja de Datos

CONTADORES

H7CN-XLN

1/16 DIN, solo contador con preselección con LED indicador de visualización.
Elección de conteo ascendente y descendente.
Velocidad de hasta 5 K conteos por segundo.
Tensiones de alimentación de CA o CC.
Modelos de salida contacto de estado sólido.
Pantalla de 8 mm de alto.

Servicios complementarios


1 Autamatización Industrial

Realizamos soluciones innovadoras y óptimas en cada área de aplicación para automatizar sus máquinas y fábricas de forma económica y flexible logrando una mayor eficiencia energética en los procesos.

2 Instrumentación

Contamos con un conjunto de aparatos electricos y/o electrónicos que permiten cuantificar en forma digital o analógica los valores de las diferentes variables a ser medidas y por lo tanto controladas.

3 Montaje

Si no cuenta con los conocimientos técnicos para montar cada una de las partes de su línea de producción, usted necesita este tipo de servicios, contamos con varios años de experiencia.